|
BS Standard Inconel 600 Nickel Based Alloy Coil for Resistant to corrosive media
Inconel 600 is a nickel-chromium alloy with good oxidation resistance at higher temperatures, with good resistance in carburizing and chloride containing environments.
Inconel 600 is a nickel-chromium alloy designed for use from cryogenic to elevated temperatures in the range of 2000 deg F(1093 deg C). The high nickel content of the alloy enables it to retain considerable resistance under reducing conditions and makes it resistant to corrosion by a number of organic and inorganic compounds. The nickel content gives it excellent resistance to chloride-ion stress-corrosion cracking and also provides excellent resistance to alkaline solutions.
Its chromium content gives the alloy resistance to sulfur compounds and various oxidizing environments. The chromium content of the alloy makes it superior to commercially pure nickel under oxidizing conditions. In strong oxidizing solutions like hot, concentrated nitric acid, 600 has poor resistance. Alloy 600 is relatively un-attacked by the majority of neutral and alkaline salt solutions and is used in some caustic environments. The alloy resists steam and mixtures of steam, air and carbon dioxide.
Alloy 600 is non-magnetic, has excellent mechanical properties and a combination of high strength and good workability and is readily weldable. Inconel 600 exhibits cold forming characteristics normally associated with chromium-nickel stainless steels.
Typical corrosion applications include titanium dioxide production (chloride route), perchlorethylene syntheses, vinyl chloride monomer (VCM), and magnesium chloride. Alloy 600 is used in chemical and food processing, heat treating, phenol condensers, soap manufacture, vegetable and fatty acid vessels and many more.
| Material |
Monel/Inconel/Hastelloy/Duplex Steel/PH Steel/Nickel Alloy |
| Shape |
Round,Forging,Ring,Coil,Flange,Disc,Foil,Spherical,Ribbon,Square,Bar,Pipe,Sheet |
Grade |
Duplex: 2205(UNS S31803/S32205),2507(UNS S32750),UNS S32760(Zeron 100),2304,904L |
| |
Others:253Ma,254SMo,654SMo,F50(UNSS32100)F60,F61,F65,1J22,N4,N6 etc |
| |
Alloy : Alloy 20/28/31 |
| |
Hastelloy:HastelloyB/ -2/B-3/C22/C-4/S/ C276/C-2000/G-35/G-30/X/N/g |
| |
Hastelloy B / UNS N10001,Hastelloy B-2 / UNS N10665 / DIN W. Nr. 2.4617,Hastelloy C,
Hastelloy C-4 / UNS N06455 / DIN W. Nr. 2.4610,Hastelloy C-22 / UNS N06022 / DIN W. Nr. 2.4602,
Hastelloy C-276 / UNS N10276 / DIN W. Nr. 2.4819,Hastelloy X / UNS N06002 / DIN W. Nr. 2.4665 |
| |
Haynes: Haynes 230/556/188 |
| |
Inconel 600/601/602CA/617/625/713/718/738/X-750,Carpenter 20 |
| |
Inconel 718 / UNS N07718 / DIN W. Nr. 2.4668,Inconel 601 / UNS N06601 / DIN W. Nr. 2.4851,
Inconel 625 / UNS N06625 / DIN W. Nr. 2.4856,Inconel 725 / UNS N07725,Inconel X-750 / UNS N07750 / DIN W. Nr. 2.4669,Inconel 600 / UNS N06600 / DIN W. Nr. 2.4816 |
| |
Incoloy: Incoloy 800/800H/800HT/825/925/926; |
| |
GH: GH2132,GH3030,GH3039,GH3128,GH4180,GH3044 |
| |
Monel: Monel 400/K500/R405 |
| |
Nitronic: Nitronic 40/50/60; |
| |
Nimonic: Nimonic 75/80A/90/A263 ; |
Specification |
Wire: 0.01-10mm
Strip: 0.05*5.0-5.0*250mm
Bar: φ4-50mm;Length 2000-5000mm
Pipe: φ6-273mm;δ1-30mm;Length 1000-8000mm
Sheet: δ 0.8-36mm;Width 650-2000mm;Length 800-4500mm |
Product
Characteristics |
1.According to the preparation process can be divided into deformation superalloys,
casting superalloys and powder metallurgy superalloys.
2.According to the strengthening mode, there are solid solution strengthening type, precipitation
strengthening type, oxide dispersion strengthening type and fiber strengthening type, etc.. |
| Standard |
GB,AISI,ASTM,DIN,EN,SUS,UNS etc |
| Inspection |
ISO,SGS,BV and so on. |
Application |
High temperature components such as turbine blades, guide vanes, turbine disks,
high pressure compressor disks,machine manufacturing
and combustion chambers used in the manufacture of aviation, naval and industrial gas turbines |
Packaging |
1. cases packed in wooden cases
2. paper packaging
3. plastic packing
4. foam packaging
Packaging according to customer requirements or products |
| Delivery |
7-25days orAccording to the product |
Payment |
L/C,D/A,D/P,T/T,Western Union,MoneyGram,According to customer requirements payments
for offline orders. |
Characteristics
- Resistant to a wide range of corrosive media. The chromium content gives better resistance than Alloy 200 and 201 under oxidizing conditions, at the same time the high nickel gives good resistance to reducing conditions.
- Virtually immune to chlorine ion stress corrosion cracking.
-
- Demonstrates adequate resistance to organic acids such as acetic, formic and stearic.
- Excellent resistance to high purity water used in primary and secondary circuits of pressurized nuclear reactors.
- Little or no attack occurs at room and elevated temperatures in dry gases, such as chlorine or hydrogen chloride. At temperatures up to 550C in these media, this alloy has been shown to be one of the most resistant of the common alloys.
- At elevated temperatures the annealed and solution annealed alloy shows good resistance to scaling and has high strength.
- The alloy also resists ammonia bearing atmospheres, as well as nitrogen and carburizing gases.
- Under alternating oxidizing and reducing conditions the alloy may suffer from selective oxidation.
Applications
- Thermocouple sheaths.
-
- Ethylene dichloride (EDC) cracking tubes.
-
- Conversion of uranium dioxide to tetrafluoride in contact with hydrofluoric acid.
- Production of caustic alkalis particularly in the presence of sulfur compounds.
-
- Reactor vessels and heat exchanger tubing used in the production of vinyl chloride.
- Process equipment used in the production of chlorinated and fluorinated hydrocarbons.
- In nuclear reactors uses are for such components as control rod inlet stub tubes, reactor vessel components and seals, steam dryers and d separators in boiling water reactors. In pressurized water reactors it is used for control rod guide tubes and steam generator baffle plates etc.
- Furnace retort seals, fans and fixtures.
-
- Roller hearths and radiant tubes, in carbon nitriding processes especially.
INCONEL Alloy 600
Inconel 600 is non-magnetic, has excellent mechanical properties and a combination of high strength and good workability and is readily weldable. Alloy 600 exhibits cold forming characteristics normally associated with chromium-nickel stainless steels.
600 sheet and plate are almost exclusively supplied in the annealed condition. Bar stock may need to be stress relieved, or annealed before performing any heading operations.
Chemistry
Chemical Requirements |
| |
Ni |
C |
Mn |
Cr |
S |
Si |
Fe |
| |
Max |
|
|
|
.15 |
|
1.0 |
|
17.0 |
|
.015 |
|
.5 |
|
10.0 |
|
| |
Min |
|
72.0 |
|
|
|
|
|
14.0 |
|
|
|
|
|
6.0 |
|
Tensile Data
Mechanical Property Requirements |
| |
Ultimate Tensile |
Yield Strength (0.2% OS) |
Elong. in 2 in. or 50mm or 4D, min., % |
R/A |
Hardness |
| |
Cold Worked/As worked |
|
| |
Min |
|
110 KSi |
|
85 KSi |
|
10 |
|
|
|
|
|
| |
Max |
|
|
|
|
|
|
|
|
|
|
|
| |
Min |
|
760 MPa |
|
585 KSi |
|
|
|
|
|
|
|
| |
Max |
|
|
|
|
|
|
|
|
|
|
|
| |
Hot Worked/As Worked |
|
| |
Min |
|
90 KSi |
|
40 KSi |
|
25 |
|
|
|
|
|
| |
Max |
|
|
|
|
|
|
|
|
|
|
|
| |
Min |
|
620 MPa |
|
275 MPa |
|
|
|
|
|
|
|
| |
Max |
|
|
|
|
|
|
|
|
|
|
|
D- Forging quality is furnished to chemical requirements and surface inspection only. No mechanical properties required.
Specifications
|
Form |
Standard |
|
Metal Type |
UNS N06600 |
|
Bar |
ASTM B166 AMS 5665 Din 17752 |
|
Wire |
|
|
Sheet |
ASTM B168 AMS 5540 Din 17750 |
|
Plate |
ASTM B168 AMS 5540 Din 17750 |
|
Tube |
ASTM B167 |
|
Pipe |
ASTM B167 |
|
Fitting |
ASTM B366 |
|
Forging |
ASTM B564 Din 17754 |
|
Weld Wire |
FM 82/ ERNiCr-3 |
|
Weld Electrode |
FM 182/ ENiCrFe-3 |
|
Din |
2.4816 |
Machining
Machinability Ratings
| MACHINING DATA |
Carbide tools are suggested
For Rates Better Than 50% Of Type 304. |
| |
Machining Type |
|
Suggested starting rates are: |
|
| |
Single Point Turning : |
|
Roughing - 0.15" depth, 0.015"/rev feed -175 SFM
Finishing - 0.025" depth, 0.007"/rev feed - 200 SFM |
|
| |
Drilling : |
|
1/4" Dia hole - 0.004"/rev feed - 60 SFM
1/2" Dia hole - 0.007"/rev feed - 60 SFM
3/4" Dia hole - 0.010"/rev feed - 60 SFM |
|
| |
Reaming : |
|
Feed - same as drilling - 100 SFM |
|
| |
Side And Slot Milling : |
|
Roughing - 0.25" depth - 0.007"/tooth feed - 125SFM
Finishing - 0.050" depth - 0.009"/tooth feed - 140SFM |
|
|
){kind=link}