410 is the basic, general purpose martensitic stainless steel that is used for highly stressed parts and provides good corrosion resistance plus high strength and hardness. Alloy 410 contains a minimum of 11.5% chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild chemical environments. It is a general purpose grade that is often supplied in the hardened but still machineable condition for applications where high strength and moderate heat and corrosion resistance are required. Alloy 410 displays maximum corrosion resistance when it's been hardened, tempered, and then polished.
TP410 S41000 is martensitic stainless steel with high mechanical properties and is ferromagnetic in the annealed or hardened condition. 410 contains the minimum amount of chromium to impart stainless steel properties. 410 resists oxidation and scaling up to 1200 degF. Hardness is one of 410's best features; It resists abrasion and wear better than most 300 series stainless steel. Grade 410 is often supplied in the hardened, but still machinable condition, for applications where high strength and moderate heat and corrosion resistance are required
410 Stainless Steel is the basic, general purpose, hardenable martensitic stainless steel. It is used for highly stressed parts with good corrosion resistance and strength. Alloy 410 resists corrosion in mild atmospheres, steam, and many mild chemical environments. The alloy can be heat treated to obtain high strength with good ductility.This alloy is used where strength, hardness, and/or wear resistance must be combined with corrosion resistance.
410 Stainless Steel is a hardenable, straight-chromium stainless steel which combines the superior wear resistance of high carbon alloys with the excellent corrosion resistance of chromium stainless steel. Oil quenching this alloy from temperatures between 1800°F to 1950°F (982-1066°C) produces the highest strength and/or wear resistance as well as corrosion resistance. A range of as-quenched hardnesses is achieved by varying the carbon level from .15% maximum in Alloy 410.
Martensitic stainless steel are optimised for high hardness, and other properties are to some degree compromised. Fabrication must be by methods that allow for poor weldability and usually the need for a final heat treatment. Corrosion resistance of the martensitic is lower than that of the common austenitic grades, and their useful operating temperature range is limited by their loss of ductility at sub-zero temperatures and loss strength by over-tempering at elevated temperatures.
410 Stainless Steel Chemical Composition:
ASTM A240 410 Stainless Steel Chemical Composition(weight%)
| C |
Mn |
P |
S |
Si |
Ni |
Cr |
Fe |
| 0.08-0.15 Max. |
1.00 Max. |
0.040 Max. |
0.030 Max. |
1.00 Max. |
0.75 Max |
11.5 - 13.5 |
Balance |
EN 10088-3 1.4006 Stainless Steel Chemical Composition (weight%)
| C |
Mn |
P |
S |
Si |
Ni |
Cr |
Fe |
| 0.08-0.15 |
1.50 Max. |
0.040 Max. |
0.030 Max. |
1.00 Max. |
0.75 Max |
11.5 - 13.5 |
Balance |
ASME SA240 SA240M TP410S Stainless Steel Chemical Composition (weight%)
| C |
Mn |
P |
S |
Si |
Ni |
Cr |
Fe |
| 0.08 Max. |
1.00 Max. |
0.040 Max. |
0.030 Max. |
1.00 Max. |
0.60 Max |
11.5 - 13.5 |
Balance |
EN 10088-3 1.4000 Stainless Steel Chemical Composition (weight%)
| C |
Mn |
P |
S |
Si |
Ni |
Cr |
Fe |
| 0.08 Max |
1.00 Max. |
0.040 Max. |
0.030 Max. |
1.00 Max. |
|
12.0 - 14.0 |
Balance |
410 Stainless Steel Mechanical Properties:
Yield Strength
0.2% Offset |
Ultimate Tensile
Strength |
Elongation
in 2 in. |
Hardness |
| Psi |
(MPa) |
Psi |
(MPa) |
% |
(max) |
| 42,000 |
290 |
74,000 |
510 |
34 |
96 |
410 Stainless Steel Applications:
Applications requiring moderate corrosion resistance and high mechanical properties are ideal for Alloy 410. Examples of applications that frequently used Alloy 410 include:
- Cutlery
- Steam and gas turbine blades
- Kitchen utensils
- Bolts, nuts, screws
- Pump and valve parts and shafts
- Mine ladder rugs
- Dental and surgical instruments
- Nozzles
- Hardened steel balls and seats for oil well pumps
Cold Rolled Stainless Steel Sheet
* Thickness: 0.3mm - 16.0mm
* Width: 1000mm, (4′)1220mm, 1500mm, 1800mm, 2000mm
* Length: Cut as per customer's requirements
* Standard Size: 1000*2000mm, 1219*2438mm, 1220*2440mm, 1250*2500mm, 1500*3000mm, 1500*6000mm, 1800*6000mm, 2000*6000mm, 4'*8'
* Edge: Mill Edge/Slit Edge
* Technique: Cold Rolled
* Surface: 2B/BA/HL/8K mirror/BA/2D/ Titanium coating with Filim
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc.
* Processing Service: Bending, Welding, Decoiling, Punching, Cutting, etc.
Hot Rolled Stainless Steel Sheet
* Thickness: 3.0mm - 300mm
* Width: 1000mm, (4′)1220mm, 1500mm, 1800mm, 2000mm-3000mm
* Length: Produce as per customer's requirements
* Standard Size: 1000*2000mm, 1219*2438mm, 1220*2440mm, 1250*2500mm, 1500*3000mm, 1500*6000mm, 1800*6000mm, 2000*6000mm, 4'*8'
* Edge: Mill Edge/Slit Edge
* Technique: Hot Rolled
* Surface: No.1/1D/Pickling
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc.
* Processing Service: Bending, Welding, Decoiling, Punching, Cutting, etc.
Cold Rolled Stainless Steel Coil
* Thickness: 0.4mm - 6.0mm
* Width: 1000mm, (4′)1220mm, 1500mm, 2000mm
* Length: Depends on Coil Weight
* Standard Size: 1000*C, 1219*C, 1220*C, 1250*C, 1500*3000mm, 1500*C, 1800*C, 2000*C, 4'*C
* Edge: Mill Edge/Slit Edge
* Technique: Cold Rolled
* Surface: 2B/No.4/HL/8K/BA
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc.
* Processing Service: Bending, Welding, Decoiling, Punching, Cutting, etc.
Hot Rolled Stainless Steel Coil
* Thickness: 3.0mm - 16mm
* Width: 1000mm, (4′)1220mm, 1500mm, 1800mm, 2000mm,2200mm
* Length: Depends on Coil Weight
Standard Size: 1000*C, 1219*C, 1220*C, 1250*C, 1500*3000mm, 1500*C, 1800*C, 2000*C, 4'*C
* Edge: Mill Edge/Slit Edge
* Technique: Hot Rolled
* Surface: No.1/1D
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc.
* Processing Service: Bending, Welding, Decoiling, Punching, Cutting, etc.
Cold Rolled Stainless Steel Strip
* Thickness: 0.002mm - 3.0mm
* Width: 5mm - 900mm
* Length: Depends on Coil Weight
* Edge: Slit Edge
* Technique: Cold Rolled
* Surface: 2B/BA/HL/8K mirror/BA/2D
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc.
Hot Rolled Stainless Steel Strip
* Thickness: 0.002mm - 16.0mm
* Width: 5mm - 900mm
* Length: Depends on Coil Weight
* Edge: Slit Edge
* Technique: Hot Rolled
* Surface: 1D/Pickling
* Standard: ASTM A240/A480M, ASTM B 668, ASTM B168/SB168, ASTM B443/SB443, JIS G4303, G4305, BS 1449, DIN 17441 etc.
*Grade: 201, 301, 304, 304L, 316, 316L, 316Ti, 321, 317L, 310S, 347H, 410, 420, 409L, 430, 440C, 444, 441, S32760, 2205, 904L, 630, 631, 253Ma, 254SMo, Incoloy 926, Inconel 625, Monel 400 etc
Hot Rolled Stainless Steel Checkered Plate
* Thickness: 1.0mm - 10mm
* Width: 600mm - 1800mm
* Length: 2000mm - 6000mm
* Edge: Mill Edge/Slit Edge
* Technique: Hot Rolled
* Surface: No.1/1D/Pickling
* Standard: ASTM A240/A480
* Grade: 304, 316L, 430
* Pattern: Chequered pattern, diamond pattern, lentils pattern, leaves pattern, etc.
Q: What kind of ZYTC company?
A: ZYTC is a professional manufacturer of metals and alloy productions and has its own warehouse with more than 30,000 tons capacity. We are working hard to open up the international market. At the same time, we will encounter a variety of purchase orders, In order to meet customer requirements and improve services, we will also distribute some kinds of metal products, of course, our strict procurement management and quality management departments can guarantee excellent quality of all products.
Q: What certificate does ZYTC have?
A: ZYTC acquired the ISO 14001 environmental management system certificate, 0HSAS18001 occupational health and safety management system certificate, and ISO 9001 quality management system certificate.
Q: What's your purchasing system?
A: Our procurement system adopts the 5R principle to ensure the "right quality" from the "right supplier" with the "right quantity" of materials at the "right time" with the "right price" to maintain normal production and sales activities. At the same time, we strive to reduce production and marketing costs to achieve our procurement and supply goals: close relationships with suppliers, ensure and maintain supply, reduce procurement costs, and ensure procurement quality.
Q: Who are your cooperate partners?
A: ZYTC has a very good relationship with world-known factories, such as Baosteel, TISCO, ZPSS, JISCO, ATl, SMC, HAYNES, VDM, ArcelorMittal, etc.
Q: What are your company's payment methods?
A: 30% T/T deposit, 70% T/T balance payment before shipment. More payment methods depend on your choices.
Q: Can you accept small orders?
A: If we have the exact materials in stock, we can deliver even 1 piece. If we don't have the goods in stock, the MOQ is normally 1 ton.
Q: Do you guarantee the safe and reliable delivery of products?
A: Yes, we always use high-quality packaging for shipping. We usually pack the products with a soft material such as polyethylene foam and then pack them in wooden cases to ensure the safety of the product in the process of transportation.
Q: Does ZYTC provide processing services?
A: Yes, we also provide processing services to the outside world, and providing professional services is one of our goals. Such as bending, water cutting, laser cutting, digging holes, welded, slit coil, and other processing according to the drawings.
Q: How to guarantee the quality?
A: Each production procedure will be subject to testing and evaluation. from the very choice of raw materials to the package for shipment. Only the products surviving all the tests are delivered for export.
Q: What if there is a quality problem?
A: We also keep a piece of the sample before shipping. After comparing the buyer's test result, and it turns out to be our problem, we will return the money back and pay for your lost or delivery of qualified materials again.
Q: Can you provide samples?
A: As a professional company, we know that the quality of products is valued by each customer, especially for international trade, we understand the customer's worries, so we can provide samples to customers, and we can ensure the consistency of the quality of samples and batch product products. The sample is free, but the buyer should pay the freight fee. And the freight fee will be returned in the future order.
Q: How about the delivery time?
A: Stock products can be shipped within 3 days. Customized product delivery time is normally 25 working days, but it is also influenced by the specific requirements or the order quantity. Partial shipment is allowed.
Audited Supplier 
410 is the basic, general purpose martensitic stainless steel that is used for highly stressed parts and provides good corrosion resistance plus high strength and hardness. Alloy 410 contains a minimum of 11.5% chromium which is just sufficient enough to demonstrate corrosion resistance properties in mild atmospheres, steam, and many mild chemical environments. It is a general purpose grade that is often supplied in the hardened but still machineable condition for applications where high strength and moderate heat and corrosion resistance are required. Alloy 410 displays maximum corrosion resistance when it's been hardened, tempered, and then polished.
){kind=link}
){kind=link}